Viper

Is this the Norma?

Walmart, camofire.com, classifieds, craigslist...

I made my own with carpet on the bottom. They don't wear out.

gotta have a good rest. Did you get yours yet? What are you putting it on?

Yeah, I considered that. After some research I found that the lighter sporter barrels may need the foreward stock contact to dampen the barrel whip. We'll see.

I did Sunday. It wasn't grouping very well...about 2". I loosened the forward action screw a 1/8 turn and the groups tightened up to nearly 1". The original torque was 60 inch pounds. After I got home, I did more reseach and found that torque can very from 35 - 65 inch lbs. I took it apart and re-torqued it to 40. I need another outing to see how it does. I'll take my equipment and make adjustments in the field. To be fare, my shooting bench setup wasn't that great. I will have a better setup next time.

I need the tires but not the wheels.

You need to kill that buck!....You gotta put on your "death face" and turn on kill mode...I call it "eye of the tiger"

Them's some nice....abs. I'm suddenly interested in crossfit. https://www.youtube.com/watch?v=tMiR4CkPcYM

Remember to pivot at the hips, not your arms. If you can, draw parallel to the ground as if you are drawing to shoot a target at the range, then pivot at the hips to come on target. Your upper body torque may be yanking your arrow high.

Do you ever make it into the big city....SE Phoenix/Chandler area?

How much $$?

I have a December WT rifle tag, so I will mainly be scouting. May have my bow along just in case.

Thanks...sounds like I should give these a go. My concern is bullet performance at lower velocities of .243 and .270 at 500 - 600 yards.

I don't think the eldx ammo is available in .243 or .270.

I checked the fit of the recoil lug. The lug fits tight against the aluminum block and the bolt holes are lined up, so it should be good without bedding, unless there are accuracy issues. There is a lot of space forward of the lug. If I do decide to bed the lug, what epoxy is recommended? They all seem to have mixed reviews.

I asked a similar question regarding .270 factory ammo. Got good feedback. Here is the link...might be helpful. http://www.coueswhitetail.com/forums/topic/67394-which-factory-ammo-to-extend-rangeaccuracy-of-my-270/

Is there a bad consequence to sanding it down anyway, to float the barrel? A floated barrel is a good thing...right? Yes and No, depends (How's that for an answer!!) Remington piller beds; that's what those bumps are, cheaper way to piller bed it, Shoot it for accuracy, also, take a screwdriver or torx or allen (whatever is on the gun) and try slightly adjusting the tension on the action, Sometimes just a tweak on the recoil or trigger guard will change POI and tighten or spread groups. Free floating is typically better BUT if the stock is flimsy at the forend and you rest it on a rock you've just created a pressure point you did not have during sighting in. I've had bad luck with B&C stocks too much play at recoil to the point of shearing a bolt after 3 shots, LITERALLY I threw the stock in the trash, then took it out and stuck it in a corner. When I started 'smithing I needed experience glass bedding so I did, WHAT A DIFFERENCE, it's now on my go to deer rifle (SAKO 243). Yours seems to fit better than mine, but still check the spacing around the recoil lug and bolt or be prepared to cuss and visit a smith to have the recoil bolt removed - not an easy or cheap task. Mine was off center and about twice too large but I didn't notice it. What is a recoil bolt? Is it specific to Sako? I take it to mean the forward action bolt, nearest the recoil lug....and the trigger guard bolt refers to the rear action bolt....? It makes sense. Loosen or tighten the forward action bolt would put less/more pressure on the "speed bumps" barrel pressure.

"Help me judge this buck guys" Innocent......no, seriously 103....and 7/8.....no, seriously....

Is there a bad consequence to sanding it down anyway, to float the barrel? A floated barrel is a good thing...right?

Ah hah...that's the only site that mentions that. Well, I like it so far. Got it put together last night. Did a little cleanup of the contact areas. Otherwise, the action/barrel slipped right in.

Oh...I didn't notice that statement. Did you see that on the B&C site? I bought the stock from Stocky Stocks.

Man! That really stinks! I pray you recover your gear. It makes me think...my gear is always laying out. I have a Eberlestock X2 I won't be using anytime soon, if you need to borrow it. I have the older version and the newer version.

I'll take them. I'll PM you to make arrangements. Thanks

Wow! Very nice.