AZorion

….

Bump

PM sent

I have not been able to get back out and test out the theories on the dimple. I have loaded up some LRP Hornady brass. I think that may have been the issue since it had no problems with factory ammo with large primers.

Ok so I have seen something that I have never seen before. I have been reloading for over ten years and have never seen a primer dimple outward before. I am reloading 6.5 Creedmoor with Hornady 140 grain ELD-M bullets. I resized brand new Lapua brass and trimmed to .01 inches (1.910") from the max length and used CCI small primer seated in the pocket. I was loading up a ladder test with Superformance and Staball 6.5. I loaded up 3 grains below max charge and was going up .2 grains from there, the first round dimpled outward at 42.2 grains of Staball 6.5. Never seen it and the speed on the crony was 2580. I am shooting a new Uintah Precision AR10 with a bolt action on the upper, so not a standard bolt with a spring behind it. It has a precision trigger on the lower from Uintah. So basically the firing pin is a free floating pin much like a gas gun. Would this be over pressure? The next round had a soft strike on the primer and failed to fire, I tried again and it failed to fire, but there was a small dimple on the primer. I tried to fire a third time and it fired and made an outward dimple same as the first primer. Would this be cause by the free floating firing pin? When I fired factory Hornady 143 ELD-X, no issues at all and the primer looked like a normal fired primer. Any suggestions? D919F245-A52B-4FDD-816F-86C102C693C8.heic

Will do, that would let me know the amount that I am resizing……will also check my reloading dies first to see if I had them adjusted correctly. Thanks for the advice!!! I was just panicking a bit since I have never had this happen,,,,,never too old to learn!!!

I have the Hornady gauge that will give me the shoulder measurement, is that what you are talking about?

What was really a mystery to me was the light firing pin misfires on the primers, almost as if the pin was too short.

I will post a pic of the bolt face soon,,,,,no, did not feel any gas on my face

Finally was able to post the picture

H1000 and H 4350 is gone from what I saw.

I also have some Fed Mag primers to trade for the RL19 powder as well.

Looking to see if anyone has a couple of pounds to sell or trade? I have IMR 7828SSC for a trade.

For sale, some items for a F 250 2017+ 6.75 foot bed: BAX Flip MX 4 hard tonneau cover for a F 250 Super Duty, 2 years Old- $700.00 I also have a heavy duty rubber bed mat for a F 250 Super Duty 6.75 foot bed, two years old - $50.00 Last is a set of Sumo springs for a F 250 Super Duty 2017+, only 2 months old - $180.00 I am selling these items because I upgraded to a 2019 F 350 Dually.

Bump

Last bump before it goes on RVtrader.

I am selling this popup trailer, great for hunting in remote places, high clearance and room for a quad up front or camping gear. Manual crank for the lid Has some flaws as this was used many times a year, I will include photos for the minor tears in the trailer. I will include photos later, serious inquiries only!! John

Bump

BUMP With pictures

Will get the photos on here soon, out of town right now on business.

Bump

BUMP

Chompy, I will take it!!!!

I have a box of 20 6.5 PRC Hornady Precision Hunter Ammo in 143 grain ELD-X, I mistook the box at Cabelas for a 6.5 Creed, so my mistake of 43 dollars is someones gain. Cabelas will not take it back of course, so I live in the West Valley and will sell for 30 buck. John